行业资讯
Company News
模具术语翻译
时间:2021-07-18 18:00:00 标签:

一、入水:gate
进入位: gate location
水口形式:gate type
大水口:edge gate
细水口: pin-point gate
水口大小:gate size
转水口: switching runner/gate
唧嘴口径: sprue diameter

二、流道: runner
热流道: hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形流道:round(full/half runner
流道电脑分析:mold flow analysis
流道平衡:runner balance
热嘴: hot sprue
热流道板:hot manifold
发热管:cartridge heater
探针: thermocouples
插头: connector plug
插座: connector socket
密封/封料: seal

三、运水:water line
喉塞:line lpug
喉管:tube
塑胶管:plastic tube
快速接头:jiffy quick connector plug/socker

四、模具零件: mold components
三板模:3-plate mold
二板模:2-plate mold
边钉/导边:leader pin/guide pin
边司/导套:bushing/guide bushing
中托司:shoulder guide bushing
中托边L:guide pin
顶针板:ejector retainner plate
托板: support plate
螺丝: screw
管钉:dowel pin
开模槽:ply bar scot
内模管位:core/cavity inter-lock
顶针: ejector pin
司筒:ejector sleeve
司筒针:ejector pin
推板:stripper plate
缩呵:movable core,return core core puller
扣机(尼龙拉勾):nylon latch lock
斜顶:lifter
模胚(架): mold base
上内模:cavity insert
下内模:core insert
行位(滑块): slide
镶件:insert
压座/斜鸡:wedge
耐磨板/油板:wedge wear plate
压条:plate 
撑头: support pillar
唧嘴: sprue bushing
挡板:stop plate
定位圈:locating ring
锁扣:latch
扣鸡:parting lock set
推杆:push bar
栓打螺丝:S.H.S.B
顶板:eracuretun
活动臂:lever arm
分流锥:spure sperader
水口司:bush
垃圾钉:stop pin
隔片:buffle
弹弓柱:spring rod
弹弓:die spring
中托司:ejector guide bush
中托边:ejector guide pin
镶针:pin
销子:dowel pin
波子弹弓:ball catch
喉塞: pipe plug
锁模块:lock plate
斜顶:angle from pin
斜顶杆:angle ejector rod
尼龙拉勾:parting locks
活动臂:lever arm
复位键、提前回杆:early return bar
气阀:valves
斜导边:angle pin
术语:terms
承压平面平衡:parting surface support balance
模排气:parting line venting
回针碰料位:return pin and cavity interference
模总高超出啤机规格:mold base shut hight
顶针碰运水:water line interferes withejector pin
料位出上/下模:part from cavith (core) side
模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件: Do not use (core/cavity) insert
用铍铜做镶件: use beryllium copper insert
初步(正式)模图设计:preliinary (final) mold design
反呵:reverse core
弹弓压缩量:spring compressed length
稳定性好:good stability,stable
强度不够:insufficient rigidity
均匀冷却:even cooling
扣模:sticking
热膨胀:thero expansion
公差:tolorance
铜公(电极):copper electrode 

angle pin. finger cam  (-:-) 斜销  
angled-lift. splits  (-:-) 斜滑块  
backing plate. supprr plate  (-:-) 支承板  
baffle  (-:-) 隔板  
cartridge heater  (-:-) 管式加热器  
cavity (of a mould)  (-:-) 型腔  
cavity splits  (-:-) 凹模拼块  
cavity-retainer plate  (-:-) 凹模固定板  
chase. bolster. frame  (-:-) 模套  
clamping force. locking force  (-:-) 锁模力  
clog-leg cam  (-:-) 弯销  
cold-slug well  (-:-) 冷料穴  
compression mould  (-:-) 压缩模  
cooling channel. cooling line  (-:-) 冷却通道  
core splits  (-:-) 型芯拼块  
core splits  (-:-) 型芯   
core-pulling distance  (-:-) 抽芯距  
core-pulling force  (-:-) 油芯力  
core-retainer plate  (-:-) 型芯固定板  
dejection plate. ejector plate  (-:-) 推板  
direct gate spruce gate   (-:-) 直接浇口  
director guide fush. ejector bushing  (-:-) 推板导套  
disk gate  (-:-) 盘形浇口  
draft   (-:-) 脱模斜度  
edge gate  (-:-) 侧浇口  
ejection force  (-:-) 脱模力  
ejector guide pillar. ejector guide pin  (-:-) 推板导柱  
ejector housing. mould base leg   (-:-) 支架  
ejector pad   (-:-) 推块  
ejector pin  (-:-) 推出零件/推杆  
ejector pin with cylindrical head  (-:-) 圆柱头推杆  
ejector plate return pin. push-back pin  (-:-) 复位杆  
ejector retainer plate  (-:-) 推杆固定板  
ejector sleeve  (-:-) 推管  
ejector tie rod  (-:-) 连接推杆  
fan gate   (-:-) 扇形浇口  
feed system  (-:-) 浇注系统  
finger guide plate  (-:-) 斜槽导板  
fixed clamp plate, top clamping plate. top plate  (-:-) 定模座板  
fixed compression mould   (-:-) 固定式压缩模  
fixed transfer mould  (-:-) 固定式压注模  
flash groove, spew groove  (-:-) 排溢:溢料槽  
flash mould  (-:-) 溢式压缩模  
flat ejector pin  (-:-) 扁推杆  
force plunger, pot plunger  (-:-) 柱塞  
gate  (-:-) 浇口  
gating insert  (-:-) 浇口镶块  
guide bush. guide bushing  (-:-) 导套  
guide fush, hended. shonlder bushing  (-:-) 带头导套  
guide fush, straight. shraighr bushing  (-:-) 直导套  
guide pillar straight. straight leader pin  (-:-) 带头导柱  
guide pillar. guide pin. leader pin  (-:-) 导柱  
guide pillar. shouldered. shoulder leader pin  (-:-) 带肩导柱  
heat pipe   (-:-) 热管  
heating plate  (-:-) 加热板  
heel block, wedge block   (-:-) 楔紧块  
horingontal parting line  (-:-) 水平分型面(线)  
hot runner mould   (-:-) 热流道模  
impression cavity block. cavity plate  (-:-) 凹模  
injection mould  (-:-) 注射模  
injection mould for thermoplastics  (-:-) 热塑性塑料注射模  
injection mould for thermoses  (-:-) 热固性塑料注射模  
injection pressure  (-:-) 注射压力  
inserf (for moulding)  (-:-) 嵌件  
insulated runner mould  (-:-) 绝热流道模  
internal mould pressure. cavity pressure  (-:-) 模内压力  
internal mould pressure. cavity pressure  (-:-) 模内压力
length bolt. puller bolt  (-:-) 定矩拉杆  
loading chamber  (-:-) 加料腔  
loading chamber  (-:-) 加料腔 
locating ring  (-:-) 定位圈/限位零件  
lower clamping plate   (-:-) 下模座板  
lower mould. lower half  (-:-) 下模  
manifold block hot-runner manifold  (-:-) 热流道板(柱)  
maximum daylight, open daylight   (-:-) 最大开距  
maximum daylight, open daylight   (-:-) 最大开距
maximum daylight, open daylight   (-:-) 最大开距 
mould bases (of a injection mould)  (-:-) 模架(注射模)  
mould bases locating elements  (-:-) 锥形定位件  
mould for plastics  (-:-) 塑料成形模具  
mould for plastics  (-:-) 塑料成形模具  
mould for thermoplastics  (-:-) 热塑性塑料模  
mould for thermosets  (-:-) 热固性塑料模  
mould insert  (-:-) 镶件  
mould opening force  (-:-) 开模力  
mould plate  (-:-) 模板  
mould shut height   (-:-) 闭合高度  
moulding pressure  (-:-) 成形压力  
movable insert. loose detail  (-:-) 活动镶件  
movable insert. loose detail  (-:-) 活动镶件 
movable mould moving half  (-:-) 动模  
moving clamp plate. bottom clamping plate. bottom plate  (-:-) 动模座板  
parting line  (-:-) 分型:分型面  
pin-point gate  (-:-) 点浇口  
portable compression mould  (-:-) 移动式压缩模  
portable transfer mould  (-:-) 移动式压注模  
positive mould  (-:-) 不溢式压缩模  
projected area  (-:-) 投影面积  
projected area  (-:-) 投影面积 
puller plate. limit plate  (-:-) 定矩拉板  
punch force  (-:-) 凸模  
punch-retainer plate  (-:-) 凸模固定板  
ring gate  (-:-) 环形浇口  
runner  (-:-) 分流道  
runner plate  (-:-) 流道板  
runner puller. runner lock pin  (-:-) 分流道拉料杆  
runner stripper plate  (-:-) 推流道板  
runnerless mould  (-:-) 无浇道模  
secondary nozzle  (-:-) 二级喷嘴  
semi-positive mould  (-:-) 半溢式压缩模  
shot capacity  (-:-) 注射能力  
shot capacity  (-:-) 注射能力
shouldered ejector pin  (-:-) 带肩推杆  
shrinkage  (-:-) 收缩率  
side core. slide core  (-:-) 侧型芯  
slide glide strip  (-:-) 滑块导板  
slide. cam slide  (-:-) 滑块  
slide. core-slide  (-:-) 侧型芯滑块  
spacer parallel  (-:-) 垫块  
splits (of a mould)  (-:-) 拼块  
spoke gate spider gate  (-:-) 轮辐浇口  
spreader  (-:-) 分流锥  
spruce   (-:-) 主流道  
sprue bush sprue busing  (-:-) 浇口套  
sprue puller  (-:-) 拉料杆  
sprue puller, ball headed  (-:-) 球头拉料杆  
sprue puller, z-shaper  (-:-) 钩形拉料杆  
sprue puller. conical headed  (-:-) 圆锥头拉料杆  
sprue puller. conical headed  (-:-) 圆锥头拉料杆 
standard mould bases  (-:-) 标准模架  
standard mould bases  (-:-) 标准模架
standard mould bases  (-:-) 标准模架 
stationary mould fixed half  (-:-) 定模  
stop flock, stop pad  (-:-) 限位块  
stop pin. stop button  (-:-) 限位钉  
stripper distance  (-:-) 脱模距  
stripper distance  (-:-) 脱模距 
stripper plate  (-:-) 推件板  
stripper ring. strpper disk  (-:-) 推件环/盘  
submarine gate tunnel gate  (-:-) 潜伏浇口  
support pillar  (-:-) 支承柱  
ta be gate  (-:-) 护耳浇口  
thermal insulation board  (-:-) 隔热板  
thermal insulation board  (-:-) 隔热板 
thread plug, threaded core  (-:-) 螺纹型芯  
thread ring. threaded cavity  (-:-) 螺纹型环  
torpedo body assembly  (-:-) 鱼雷形组合体  
transfer mould  (-:-) 压注模、传递模  
upper clamping plate  (-:-) 上模座板  
upper mould, upper half  (-:-) 上模  
valve gate  (-:-) 阀式浇口  
venf (of a mould)  (-:-) 排气槽(孔)  
vertical parting line  (-:-) 垂直分型面(线)  
warm runner mould  (-:-) 温流道模  
warm runner plate  (-:-) 温流道板

  • 国际贸易英语词汇3[货款结算]
  • 微软公司标准采购订单条款和条件翻译
  • 质量认证英语翻译
  • 其他新闻
    •  随着国际之间交流与合作的日益频繁,化学英语翻译越发得到重视,它不仅对国家间的学术交流有一定影响,同样更关系到对外化工行业贸易的成败。今天我们专业翻译公司就来跟大家来聊聊有关化学专业英语翻译有哪些技巧呢?  化学专业
      2020-11-18
    • 要想学好英语,那就要掌握英语的听,说,读,写,译几个方法。很多小伙伴认为最难的就是翻译题型,这也是考试中最不好拿分的题型。下面,翻译公司给大家介绍几种英语翻译常用的方法,大家可以作为学习的参考。  一.省译法  这是与增译法相
      2017-06-27
    • 1、运用声音 译员表达时首先要吐字清晰、发音标准。译员对于听众而言就是一个发言者,要让听众听得清楚、便于理解。语音训练可以通过朗读、演讲和绕口令来进行。译员要及时发现自己的发音含糊、吐字不清等问题并作针对性
      2017-06-27

    免费咨询电话:400-600-6870
    联系电话158-9898-6870(微信同号)
    专业常州在线翻译机构_常州翻译公司  
    版权所有:常州翻译公司 常州本地化翻译 常州翻译公司收费标准 常州翻译公司 常州陪同翻译 工程技术口译翻译 儿童文学翻译 如何选择翻译公司

    友情链接

    版权所有:译声翻译网  Powered by 常州翻译公司
    全国免费咨询电话:400-600-6870  电话158-9898-6870(微信同号)